Imagen
1 vep nipple
Imagen
vep4f4 cutaway

VEP8F8-SS - VEP-Series Female Threaded Plug

¿Tienes una duda? 

Llámanos al +8183545649 o da clic en el botón de contacto para mandarnos un email.

Atributos

Weight
2.6 lb
Break Quantity
1
Paquete Opcional/Cantidad por Caja
1
Material
Acero inoxidable 316
Maximum OD
Thread
Hembra NPTF
Body Size
Working Pressure
Thread Size
Length
Hex
Flow

Detalles

Compatibilidad e Intercambio de Datos

Interchangeable with Stucchi VEP-P/VEP-HD Series, DNP PST4/FSI Series, Voswinkel FT Series, Parker FET-Series, and Holmbury HFT Series

Construcción

  • Machined components are manufactured using solid 316 stainless steel bar stock
  • Stainless steel retaining rings and springs maximize corrosion resistance and extend service life
  • Los vástagos de las válvulas tienen sellos de poliuretano moldeados, con un rango de temperatura de -65 °F a +212 °F (-54 °C a +100 °C)
  • Ancillary coupler seals are Nitrile (Nitrile Rubber), with a temperature range of-40°F to +250°F (-40°C to +121°C)
  • TPC-ET Anti-Extrusion ring protects main coupling valve seal from dynamic impulse pressure damage

Como funciona

  • Prior to connecting, thoroughly clean all mating surfaces and threads on both halves, the pull the coupler sleeve forward.
  • To initiate the connection, align the coupler and plug, pushing/turning the coupler sleeve towards the plug while engaging the threads. Keep the mating halves aligned during the connection process.
  • Allow the threads to pull the coupler onto the plug, do not push the coupler onto the plug.
  • The first phase of the connection should be threaded by hand, without the use of tools. Please note the connection sleeve may seize when dirt and debris accumulate in the threads - wipe away debris with a cloth, compressed air or a brush.
  • The second phase of the connection may require a wrench if the pressure is higher than anticipated.
  • Continue to thread the coupler sleeve onto the plug until the end of the sleeve meets the plug body.
  • To disconnect, use a wrench to break the coupler sleeve free and keep the mating halves aligned during the disconnection process.

Características

  • DORS Retention System optimizes flow and impulse pressure performance
  • Thread-to-connect design and dual valve system in the plug allow for connecting under pressure.
  • Threaded design eliminates premature wear or brinelling commonly found with locking ball designs when subjected to high impulse pressures.

Nota

  • ¹ Acoples probados por impulso de acuerdo con ISO7241-2 para 1.000.000 de ciclos conectados y 100.000 ciclos desconectados al 133% de la presión de trabajo ISO.
  • ² Acoples probados por impulso de acuerdo con ISO7241-2 durante 100.000 ciclos conectados y desconectados a la presión de impulso máxima indicada.
  • ³ La temperatura del sistema para la presión máxima de conexión/desconexión no debe exceder los 150 °F (65 °C)
  • Flujo nominal ∆P=21,75 PSI

Especificaciones

  • Maximum Impulse Pressure²: 3,000 PSI (20.68 MPa) ¹
  • Burst Pressure Connected: 15500 PSI (106 MPa)
  • Burst Pressure Plug: 20000 PSI (137 MPa)
  • Presión máxima Connect & Disconect: 3000 PSI (21 MPa)

Recursos