Imagen
vep series code 62 flange head coupler steel
Imagen
vep series flange head coupler

12VEPFH12 - Cople Serie VEP Extremo Brida “Wingstyle” Codigo 62

¿Tienes una duda? 

Llámanos al +8183545649 o da clic en el botón de contacto para mandarnos un email.

Atributos

Peso
14.2 lb
Break Quantity
1
Paquete Opcional/Cantidad por Caja
1
Material
Acero
Tamaño de Cuerpo
Puerto
1 1/2"

Detalles

Compatibilidad e Intercambio de Datos

Interchangeable with Stucchi VEP-P/VEP-HD Series, DNP PST4/FSI Series, Voswinkel FT Series, Parker FET-Series, and Holmbury HFT Series

Construcción

  • Machined components are manufactured using solid steel bar stock
  • Stainless steel retaining rings and springs maximize corrosion resistance and extend service life.
  • Steel componentry is plated using ROHS Compliant Zinc Nickel for superior corrosion resistance.
  • Valve stems have molded Polyurethane seals, with a temperature range of -65°F to +212°F (-54°C to +100°C)
  • Ancillary coupler seals are Nitrile (Nitrile Rubber), with a temperature range of -40°F to +250°F (-40°C to +121°C)
  • TPC-ET Anti-Extrusion ring protects main coupling valve seal from dynamic impulse pressure damage

Descripción

Serie VEP Acoples con cabeza de brida Código 62

Características

  • Two-stage valving to protect critical sealing components during pressurized connection & disconnection
  • Posi-Lock valve system secures valving during surge-flow conditions to prevent high-velocity damage
  • No-spill, flush face valve minimizes air inclusion during connection and spillage during disconnection.
  • Threaded design eliminates premature wear or brinelling commonly found with locking ball designs when subjected to high impulse pressures.

Como funciona

  • Prior to connecting, thoroughly clean all mating surfaces and threads on both halves, the pull the coupler sleeve forward.
  • To initiate the connection, align the coupler and plug, pushing/turning the coupler sleeve towards the plug while engaging the threads. Keep the mating halves aligned during the connection process.
  • Allow the threads to pull the coupler onto the plug, do not push the coupler onto the plug.
  • The first phase of the connection should be threaded by hand, without the use of tools. Please note the connection sleeve may seize when dirt and debris accumulate in the threads - wipe away debris with a cloth, compressed air or a brush.
  • The second phase of the connection may require a wrench if the pressure is higher than anticipated.
  • Continue to thread the coupler sleeve onto the plug until the end of the sleeve meets the plug body.
  • To disconnect, use a wrench to break the coupler sleeve free and keep the mating halves aligned during the disconnection process.

Nota

  • ¹ Acoples probados por impulso de acuerdo con ISO7241-2 para 1.000.000 de ciclos conectados y 100.000 ciclos desconectados al 133% de la presión de trabajo ISO.
  • ² Acoples probados por impulso de acuerdo con ISO7241-2 durante 100.000 ciclos conectados y desconectados a la presión de impulso máxima indicada.
  • ³ La temperatura del sistema para la presión máxima de conexión/desconexión no debe exceder los 150 °F (65 °C)
  • Flujo nominal ∆P=21,75 PSI

Especificaciones

  • Maximum Impulse Pressure² : 5800 PSI (40 MPa)
  • Burst Pressure Connected: 18000 PSI (124 MPa)
  • Burst Pressure Coupler: 12000 PSI (83 MPa)
  • Presión máxima Connect & Disconect: 3000 PSI (21 MPa)

Recursos